宋之勇,王伟力,阮建刚,白连建,傅磊
SONG Zhi-yong1,WANG Wei-li1,RUAN Jian-gang2,BAI Lian-jian3,FU Lei1(1.Department of Ordnance Science and Technology

• 1:海军航空工程学院
• 2:91049部队
• 3:92514部队

摘要(Abstract)：

为研究串联战斗部前级装药对后级随进战斗部的影响,验证在现有导弹战斗部前端加装环形聚能装药的可行性,利用ANSYS/LS-DYNA软件进行了柱锥体环形切割器壳体飞散的数值仿真,得到了在其后级随进战斗部之前的空气域中的飞散路径,获得了这部分空气域内的爆炸响应冲击波的时间-压力历程。仿真结果表明,柱锥体环形切割器壳体破裂后,以壳体端部和壳体内侧上部对后级随进战斗部的影响为主,而内侧上部壳体受爆轰波影响形成聚能侵彻体对后级随进战斗部的影响最大,这为串联战斗部中对后级随进战斗部的隔爆设计打下了基础。
To research the effect of the tandem warhead's front charge on the following warhead and verify the feasibility of installing annular shaped charge in the front of active missile's warhead,the cylindrical-conical annular cutter shell dispersion was simulated by using ANSYS/LS-DYNA software.The dispersion regurlarity of the cylindrical-conical annular cutter shell and the time-pressure figure of explosion respose shock wave in the air,which were in front of the following projectile warhead,were gained.The simulation results show that the inside upper part and the end part among all the parts of the cylindrical-conical annular cutter shell have majoy effect on the following projectile warhead,and the inside upper part has the most sirously effect,because it is affected by the detonation wave to form the similar metal jet.It can support the base for the explosion-proof design of the following projectile warhead on tandem warhead.

关键词(KeyWords)： 柱锥体环形切割器;壳体飞散;爆炸力学;冲击波;数值模拟
Cylindrical-conical annular cutter;Shell dispersion;Explosion mechanics;Shock wave;Numerical simulation

Abstract:

Keywords:

基金项目(Foundation):

作者(Author): 宋之勇,王伟力,阮建刚,白连建,傅磊
SONG Zhi-yong1,WANG Wei-li1,RUAN Jian-gang2,BAI Lian-jian3,FU Lei1(1.Department of Ordnance Science and Technology

参考文献(References)：

• (1)张先锋,陈惠武.破爆型串联战斗部前级对后级影响数值模拟[J].弹箭与制导学报,2006,26(2):66-68.
• (2)涂侯杰,恽寿榕,赵衡阳.破爆型串联战斗部第一级对第二级影响的研究[J].兵工学报,1994(3):18-22.
• (3)王健,阮文俊.串联随进战斗部前后级影响数值仿真[J].系统仿真学报,2010,22(9):2231-2234.
• (4)王树有,陈惠武,赵有守.串联攻坚战斗部前级爆轰场对后级影响分析[J].火炸药学报,2006,29(2):4-6.
• (5)曾必强,姜春兰,严翰新,等.串联攻坚战斗部前级爆轰场对随进弹随进影响分析[J].兵工学报,2010,31(增刊1):162-166.
• (6)段建,杨黔龙,周刚,等.串联战斗部前级聚能装药和隔爆结构设计与实验研究[J].高压物理学报,2006,20(2):202-206.
• (7)李永胜,王伟力,姜涛.用于串联战斗部的环形切割器优化设计[J].弹箭与制导学报,2010,30(2):93-96.
• (8)王伟力,李永胜,田传勇.串联战斗部前级环形切割器的设计与试验[J].火炸药学报,2011,34(2):39-43.
• (9)Livermore Software Technology Corporation.LS-DYNAKeyword User's Manual(971v)[M/OL].Livermore,2007.