师强强;刘为洲;杨海涛;
SHI Qiang-qiang;LIU Wei-zhou;YANG Hai-tao;Maanshan Institute of Mining Research Blasting Engineering Co.,Ltd.,Sinosteel Maanshan Institute of Mining Research Co.,Ltd.;State Key Laboratory of Safety and Health for Metal Mine,Sinosteel Maanshan Institute of Mining Research Co.,Ltd.;

• 1:中钢集团马鞍山矿山研究院有限公司马鞍山矿山研究院爆破工程有限责任公司
• 2:中钢集团马鞍山矿山研究院有限公司金属矿山安全与健康国家重点实验室

摘要(Abstract)：

为了研究定向切割中金属介质对爆炸能量传播的控制作用,采用理论计算和LS-DYNA数值模拟软件分析了孔壁初始裂缝的形成和裂缝贯穿的机理。结果表明:由于金属介质的冲击阻抗远大于水介质,沿金属介质方向传播的爆炸压力和速度都远大于其他方向,导致金属介质接触的孔壁处首先产生初始裂缝,随后在爆轰压力和"水楔"作用下裂缝失稳贯穿。有机玻璃模型实验结果表明:受金属介质的控制,模型能按照预定方向断裂出平整光滑裂缝,炮孔周围仅有少数短裂隙,证明了该技术的优势。
To study the control function of metal medium on the explosion energy transmission in directional cutting blasting,theoretical calculation and numerical software of LS-DYNA were used to analyze the mechanism of initial crack formation and crack penetration in the blasthole wall.The results indicated that the explosion pressure and velocity spread in the direction along metal medium was higher than other directions because shock wave impedance of metal medium was larger than impedance of water medium.The initial crack firstly appeared in the blasthole wall contacted with the metal medium.Then,the cracks were unstable and penetrated under the action of detonation pressure and water wedge.The PMMA model test results indicated that the model could be cut to form seams according to the predetermined direction under the effect of the metal medium.There were only a few short cracks around the blasthole.The advantage of the technology was demonstrated.

关键词(KeyWords)： 定向切割爆破;冲击波;数值模拟;有机玻璃;金属介质
Directional joint cutting blasting;Shock wave;Numerical simulation;PMMA;Metal medium

Abstract:

Keywords:

基金项目(Foundation):

作者(Authors): 师强强;刘为洲;杨海涛;
SHI Qiang-qiang;LIU Wei-zhou;YANG Hai-tao;Maanshan Institute of Mining Research Blasting Engineering Co.,Ltd.,Sinosteel Maanshan Institute of Mining Research Co.,Ltd.;State Key Laboratory of Safety and Health for Metal Mine,Sinosteel Maanshan Institute of Mining Research Co.,Ltd.;

参考文献(References)：

• [1]刘为洲,杨海涛,张西良,等.水介质定向切割爆破技术的试验研究[J].金属矿山,2015(S1):40-42.LIU Wei-zhou,YANG Hai-tao,ZHANG Xi-liang,et al.Experimental research on the aqueous medium directional cutting blasting technology[J].Metal Mine,2015(S1):40-42.
• [2]刘为洲,袁英杰,张西良,等.水力增压爆破试验[J].工程爆破,2014,20(2):10-13.LIU Wei-zhou,YUAN Ying-jie,ZHANG Xi-liang,et al.Hydraulic boosting blasting test[J].Engineering Blasting,2014,20(2):10-13.
• [3]张守中.爆炸基本原理[M].北京:国防工业出版社,1988:366-374.ZHANG Shou-zhong.Explosion fundamentals[M].Beijing:National Defence Industry Press,1988:366-374.
• [4]宗琦,李永池,徐颖.炮孔水耦合装药爆破孔壁冲击压力研究[J].水动力学研究与进展,2004,19(5):610-615.ZONG Qi,LI Yong-chi,XU Ying.Preliminary discussion on shock pressure on hole wall when water-couple charge blasting in the hole[J].Journal of Hydrodynamics,2004,19(5):610-615.
• [5]时党勇,李裕春,张胜民.基于ANSYS/LS-DYNA 8.1进行显式动力分析[M].北京:清华大学出版社,2005:184-216.SHI Dang-yong,LI Yu-chun,ZHANG Sheng-min.Dynamics analysis based on ANSYS/LS-DYNA8.1[M].Beijing:Tsinghua University Press,2005:184-216.
• [6]杨仁树,宋俊生,杨永琦.切槽孔爆破机理模型试验研究[J].煤炭学报,1995,20(2):197-200.YANG Ren-shu,SONG Jun-sheng,YANG Yong-qi.Study on the mechanism of notched-holes blasting by model experiment[J].Journal of China Coal Society,1995,20(2):197-200.
• [7]刘为洲.水介质定向切割爆破技术[R].马鞍山:马鞍山矿山研究院,1986.LIU Wei-zhou.Aqueous medium directional cutting blasting technology[R].Maanshan:Maanshan Institute of Mining Research,1986.
• [8]刘永胜,傅洪贤,王梦恕,等.水耦合定向断裂装药结构试验及机理分析[J].北京交通大学学报,2009,33(1):109-112.LIU Yong-sheng,FU Hong-xian,WANG Meng-shu,et al.Experimental research and analysis of mechanics on water-coupling directional fractural charge[J].Journal of Beijing Jiaotong University,2009,33(1):109-112.
• [9]ROSSMANITH H P,DAEHNKE A,NASMILLNER RE K,et al.Fracture mechanics applications to drilling and blasting[J].Fatigue and Fracture of Engineering Materials and Structures,1997,20(11):1617-1636.