杜学良,苟瑞君,候红霄,韩加宏
DU Xue-liang,GOU Rui-jun,HOU Hong-xiao,HAN Jia-hong(School of Chemical Engineering and Environment

• 1:中北大学化工与环境学院

摘要(Abstract)：

利用相似理论分析了线型聚能切割器(LSCC)切割钢靶板过程的相似参数,建立了该钢靶板的相似率关系。在此基础上以文献〔5〕中的线型聚能切割器为计算模型,应用ANSYS/LS-DYNA3D软件对其进行模拟,通过与试验结果对比证明了模拟的正确性。然后对满足模拟比的聚能切割器切割靶板的过程进行了模拟,对比分析了其射流头部速度及侵彻深度。结果表明,相似率模型在线型聚能切割器切割靶板过程中是成立的。
Using the analogue theory,the analogue parameters of linear shaped charge cutters(LSCC) penetrating steel target were analyzed and the analogue relations of LSCC penetrating steel target were established.The model of LSCC in the literature 5 was simulated with ANSYS/LS-DYNA software and the simulation results were proved to be correct by comparison with test results.Then the process of LSCC which satisfied the simulation ratio penetrating steel target was simulated,and the speed of jet head and the penetration depth were compared and analyzed.The numerical results indicate that the analogue rule model is tenable in the process of LSCC penetrating steel target.

关键词(KeyWords)： 线型聚能切割器;靶板;量纲理论;相似率;数值模拟
Linear shaped charge cutter;Target plate;Dimensional theory;Analogue rule;Numerical simulation

Abstract:

Keywords:

基金项目(Foundation):

作者(Author): 杜学良,苟瑞君,候红霄,韩加宏
DU Xue-liang,GOU Rui-jun,HOU Hong-xiao,HAN Jia-hong(School of Chemical Engineering and Environment

参考文献(References)：

• (1)刘维柱,方向,汪庆桃,等.线型聚能装药切割钢板过程的数值模拟[J].工程爆破,2003,9(3):15-18.
• (2)陶为俊,黄风雷,浣石.聚能射流侵彻过程的相似率及其在数值仿真中的应用[J].广州大学学报,2008,7(1):29-33.
• (3)谈庆明.量纲分析[M].合肥:中国科学技术出版社,2005.
• (4)唐密,柏劲松,李平,等.爆炸成型弹丸侵彻相似率的数值模拟研究[J].火工品,2006(2):1-4.
• (5)纪冲,龙源,杨旭,等.线型聚能切割器在工程爆破中的应用研究[J].爆破器材,2004,33(1):32-35.
• (6)Ayisit O.The Influence of Asymmetries in ShapedCharge Performance[J].International Journal of ImpactEngineering,2008,35:1399-1404.
• (7)苟瑞君.线性爆炸成型侵彻体形成机理研究[D].南京:南京理工大学.2007:75-76.
• (8)[美]Walters W P,Zukas J A.成型装药原理及其应用[M].王树魁,贝静芬等译.北京:兵器工业出版社,1992.